|
06 May 2010
| Description | LCD Display |
| While in Standby Mode, press the Func key to enter the Setup Menu. You will be prompted to enter the Administrator Password. Administrator Password (default:. 123). |
Enter Password
123
|
|
Press the Func key to continue. The setup menu will scroll down slowly as shown.
Enter 5 to select the System Configuration menu.
|
Press 1: Add/Update ID Press 5: System Configuration |
| The current date is displayed. If necessary, enter the new date and then press the Func key to continue. |
Date (M/D/Y): 08/30/1999 |
|
After pressing the Func key, the current time is displayed. Enter the new time then press the Func key to continue.
|
Time (H:M:S): 13:45:23 |
|
The system will then ask for the Terminal ID. The Terminal ID is used to identify the iGuard in your network, especially if you have installed more than one.
|
Terminal ID:
|
iGuard can keep the date & time running without power for approximately two days. Also, there is a software tool for users
to synchronize the clock of the iGuard device with the desktop PC.
The following procedures show you how to assign the name, the IP addresses, and other related settings. Collect all the information before proceeding.
| Description | LCD Display |
|
While in Standby Mode, press the Func key to enter the Setup Menu. You will be prompted to enter the
Administrator Password (default:. 123) as shown. |
Enter Password
123
|
|
Enter 5 to select the System Configuration menu. |
Press 1:
Add/Update ID
Press 5:
Add/Update ID
|
| Pressing the Func key until you see “DHCP/Static IP” | |
| Press Func key to continue, and then press 1 to select DHCP or 2 to select Static IP. | DHCP/Static IP (1/2)? Static |
| Press Func key to continue. You will then be asked to enter the IP address of the device. The default is 192.168.0.100. Enter the static IP address assigned to the device (e.g., 192.168.1.123).Note: Please configure the IP according to your corporate network. |
IP Address: 192.168.001.123 |
| Press Func key to continue. Enter the sub-net mask here (e.g., 255.255.255.0). | Subnetmask: 255.255.255.000 |
| Press Func key to continue. Enter the address of the Default Gateway (e.g., 192.168.0.200). |
Default Gateway: 192.168.000.200 |
| Press Func key to continue. Enter the address of the Domain Name Server (e.g., 192.168.0.200). Make sure that the IP address of all units are unique. (Warning: IP addresses that are not unique will cause network error and the iGuard would not function). |
DNS: 192.168.000.200 |
| Press Func key to continue. You will be asked if the device is a Master or Slave device (1/2)? If you have only one unit of iGuard, choose (1) Master. If you have more than one units of iGuard, you have to decide which is the Master and which are the Slave(s). If you choose (2) Slave, the system will ask you to provide the Master IP Address, key in, default: 192.168.0.100. Please also read the section about Master and Slave mode. | Master/Slave (1/2)? Master |
| iGuard FPS110 can be configured as Master or Slave device. Select one and then press Func key. The system will reset itself and then return to Standby Mode. | Mon Aug 30 13:46 ID #:_
|
The Company Code is introduced for the units with the Smart Card option. The Company Code is used to make sure that the unit only reads the smart cards issued by the company. For example, if the Company Code of the unit is 1234, it only reads the smart cards with the same Company Code and will ignore the cards with different company code. See Operation Manual for more information.
Follow these steps to assign & edit the three passwords:
iGuard has three "global” passwords1. The System Administrator Password is used to access the system menu and to configure the system (such as accessing the setup menu in the last example). The User Administrator Password is used to manage the user accounts. The Door Access Password is used to release the door strike in Quick Access option.
| Description | LCD Display |
|
While in Standby Mode, press the Func key to enter the Setup Menu. Enter the System Administrator Password (default 123) and press Func key, then press 6 to select "Set Password" menu. The menu "Admin/Personal(1/2)?"will display. Press 1 to select Administrator password.
|
System Admin: 123 |
| Press the to erase the old password, and enter the new password (e.g., AB456). The field size limit for individual passwords is 10 digits, from 0-9 and A/B. | System Admin: AB456 |
| Press the Func key to accept the new System Administrator Password. You will then be prompted for the User Administrator Password as shown. | User Admin: |
| Enter the new User Administrator Password (e.g.,7890BA). | User Admin: 7890BA |
| Press the Func key to accept the new User Administrator Password. You will then be prompted for the Door Access Password as shown. |
Door Access:
|
| Enter the new Door Access Password (e.g.9394AB709). It is suggested to use a long and hard-toguess password. | Door Access: 9394AB709 |
| Press Func to return to the standby mode. | Mon Aug 30 13:49 ID #: |
You must enable the Door Access Password before it can be used, by specifying the corresponding authorized time and terminals. It is disabled in the factory settings. The only way to enable it is via the Internet browser (discussed in the Manual), under the “Quick Access" page.
Fingerprint enrollment is to register a fingerprint template for later recognition. A good enrollment is crucial for all reliable fingerprint recognition systems, including the iGuard.
Each person must register two fingers: one as the primary and the other one as the secondary. In case that the primary finger is not suitable for verification such as when the finger is hurt, the person can use his/her secondary finger for the authentication process.
During the process, each fingerprint image is captured three times for minutiae analysis and extraction. If the quality of any one of the three images is not good enough, you will be asked to re-capture the three images again.
During the enrollment process, you must position the center of your fingerprint of your thumb to the center of the fingerprint sensor. The center of the fingerprint contains the most minutia points from which the fingerprint sensor can extract. A good fingerprint image captured during the enrollment process can significantly reduce the false-reject rate during later verification.
| Description | LCD Display |
|
While in standby mode, press the Func key to enter the Setup Menu. Enter the Administrator Password (default 123)and press Func key, then press 1 to select "Add /Update ID" menu. Press 1 to input fingerprint. |
By Finger/Passwd
(1/2)?
Enter ID # and scan 1st Finger
|
| Enter the user ID # (e.g. A01). The ID can be of any length from 1 character to 8 characters. | Enter ID# A01 |
| Press the Func key to confirm the ID #. Thedevice now begins to capture the 1st image of the primary finger. The horizontal bar on the second line indicates the quality of the image. Lift the sensor shutter with your right-hand thumb and place it firmly on the sensor until the quality bar reaches the right end. You may need to move and rotate the thumb a little bit to achieve the required quality. |
Scanning 1 of 3... Scanning 1 of 3... |
| After the quality bar reaches the right end, you will be asked to remove the finger from the sensor. | Analyzing. Pls remove finger... |
| When the device detects that you have removed the finger, it will ask you to place it back again for the 2nd image. | Press Func to scan 2 of 3 |
| Press the Func key and repeat the same procedure, and you will be asked to scan the 3rd time of the same primary finger. | Press Func to scan 3 of 3 |
| Press the Func key again and repeat the procedure for the third time. You will then be asked to scan the secondary finger. | Press Func to scan 2nd Finger |
| Press the Func key, and repeat the above steps to scan the left-hand thumb three times again. If all the images are OK, you will see the acknowledge message "ID: A01 Added OK!" momentary, then the device is ready for next enrollment. |
ID: A01 Added OK!
Enter ID # and
scan 1st Finger
|
| Press <-- to return to the standby mode. | Mon 30 Aug 12:00 ID # |
| In the case of dry finger (poor fingerprint image), it will warn you for dry finger. You can either wet your finger with lotion and try again, or continue. | Scanning 1 of 3 Too Dry ! |
| If continue with dry finger, at the end, it will prompt you if you want to set security to low2. We recommend to choose low security only for time attendance application. | Set Security to Low2 yes(1)/No(2)? |
This feature enables the device to identify a person without requiring the user to first enter his/her user ID, and must be turn on via the Internet browser, as described in the next section. All that needs to be done is to present your enrolled finger to the sensor and wait for it to match your fingerprint template with stored templates. Once a match is made, the door opens and the system will then return to the standby mode.
The maximum number of users allowed to access the iGuard using automatch is recommended to be limited to 30 users. This is due to the fact that the iGuard would require some time to process the fingerprint and then search for it across ALL the database stored on your iGuard. It is therefore recommended that the automatch feature is left for top management and the rest of staff can use ID plus Fingerprint for access. Also, user with poor fingerprint quality shall not use automatch.
The user has to be created prior to use this function either the fingerprint is enrolled or the password is added. After the enrollment procedure, the user ID and the fingerprint template is stored in the internal memory.
Please note that only one (the primary ) fingerprint template is stored on the smart card.
The following steps illustrate how to write the user information to a Smart Card:
|
Description
|
LCD Display |
| While in the standby mode, press the Func key to enter the Setup Menu. Enter the Administrator Password (default 123) and press Func key, then press 9 to select “Issue/Import Card" menu. Press 1 to issue Smart Card. |
Enter ID # |
| Enter the ID # you want to write to the Smart Card (e.g., A01). | Enter ID #: A01 |
| Press the Func key to confirm. You will then be asked to present the Smart Card. | Waiting for SmartCard... |
| Present a Smart Card near the keypad. The unit will then write the user information to the card. | Writing.... |
| After writing to the card, you will be asked whether or not to remove the user's fingerprint information from the internal memory. It is recommended not to remove user fingerprint information from memory. | Remove Fingerprint Yes(1)/No(2)? |
| The unit will prompt for another ID. | Enter ID # |
| Press <-- key once or wait till time out, the unit will return to the standby mode. | Mon Aug 30 12:00 ID #: |
Please note that the above procedure will overwrite all the existing informationstored in the Smart Card.
The first time a user accesses a remote unit in a remote branch with this smartcard, the user must register the Card to this unit. In addition, after registering the system administrator must also assign the departments the user belongs to, to grant the user the access rights required. After that, the user can use his/her card to access the remote unit same as the one in his/her own branch. The registration procedure reads the user information from the Smart Card, and stores the information in the Smart Card Memory of the internal user database.
The procedure is done via the Function 0 in the Setup menu, and is illustrated in the following steps:
| Description |
LCD Display
|
| While in the standby mode, press the Func key to enter the Setup Menu. Enter the Administrator Password (default 123) and press Func key, then press 9 to select “Issue/import Card" menu. Press 2to import Smart Card. | Enter ID # |
| You will then be asked to present the Smart Card. | Waiting for Smart Card... |
| Present a Smart Card near the keypad. The unit will then write the user information to the card. | Writing.... |
The device uses the enrolled fingerprint information to identify the person. The verification process is very straightforward, and is illustrated in the following steps:
| Description | LCD Display |
| While in the standby mode, key in the user ID number (e.g., A01). | Mon Aug 30 13:49 A01 |
| Lift the shutter and place either your primary finger (right-hand thumb) or your secondary finger (left-hand thumb) on the sensor. You should place the finger the same way as you did during the enrollment procedure. The device will automatically start scanning when the sensor shutter is lifted all the way up. |
Scanning... A01
Verifying...
|
| If you are authenticated, the device will open the door, and will return to the standby mode. | Mon Aug 30 13:49 ID # |
Note: there is another feature called Auto-Match, which allows the user to access the device without the need to enter his/her ID first.
The automatch feature allows users to get authorized without inputting their user ID. This feature allows top management to enter the premises without having to enter their ID, enable them quicker access and giving them high convenience.
| Description | LCD Display |
| While in Standby Mode, place either your primary or secondary finger on the sensor by lifting the shutter. The device will automatically start scanning when the sensor shutter is lifted all the way up. |
Mon Aug 30 13:49
Automatch
Mon Aug 30 13:49
Verifying...
|
| If you are authorized, the device will open the door,and will return to the standby mode. | Mon Aug 30 13:49 Authorized |
The procedure for authenticating using smart card is simple and straightforward, and it is illustrated in the following steps:
| Description | LCD Display |
| While in standby mode, present the smart card near the keypad. The unit will read the data stored in the card, and if the card is valid (i.e., it is not a blank card and with the correct company code), you will be asked to scan your finger. | Jacky Hui Waiting Finger |
| The fingerprint image matches the data stored in the card, the user is authenticated. The unit will return to the standby mode, and it is ready for the next card. | Jacky Hui Authorized |
| Description | LCD Display |
| While in standby mode, key in the user ID number (e.g., A01). | Mon Aug 30 13:49 A01 IN |
| Instead of lifting the shutter and placing the finger on the sensor, press the Func key. | Your Password: |
| Enter the personal password (e.g., 123456) | Your Password: ****** |
| Press Func key again to confirm. If the personal password is correct, the person is authenticated and the message will appear. | A01 Authorized |
You can temporary suspend a user ID. This is useful if you want to temporary stop a user from getting into your business premises, and you may want to resume his access right later on. This is done via the function “Inactive ID" in the function menu, and it is illustrated in the following steps:
| Description | LCD Display |
| While in Standby Mode, press the Func key to enter the Setup Menu. Enter the Administrator Password (default 123) and press Func key, then press 2 to select “Inactive ID" menu. | Enter ID: |
| Enter the ID # you want to suspend (e.g., A01). | Enter ID: A01 |
| Press the Func key to confirm. The ID # is suspended, and the user can no longer be authenticated. The system will return to the standby mode. | ID A01: Inactivated |
You can permanently delete a user using similar procedure as described above and it is illustrated as follows:
| Description | LCD Display |
| While in standby mode, press the Func key to enter the Setup Menu. Enter the Administrator Password (default 123) and press Func key, then press 4 to select "Delete ID" menu | ID to Delete: |
| Enter the ID # you want to delete (e.g., A01). | ID to Delete: A01 |
| Press the Func key to confirm. The ID # is deleted, and the user can no longer get access. The system will return to the standby mode. | ID #A01 Deleted |
Note: Once an employee ID is deleted, all the information associated with the employee ID, such as the fingerprint data and the access rights, will also be permanently deleted. You must re-enroll the employee if necessary.
The device can be turned off easily by just simply turning the power off. However, there is a very small chance that the unit is in the process of accessing and updating the internal flash memory at the moment when the power is discontinued. This may result in data loss.
The safe way to turn the unit off is to do a proper shut down by accessing Func 7 in the menu. You can also reset the user database and the access log with this function. In addition, you can reset all the settings to the factory default (such as setting the IP address to the default 192.168.0.100, and the terminal name to iGuard ... etc.).
This feature has been added as a safety precaution, just in case your iGuard fails to respond to you and does not unlock the door as instructed. While in the standby mode, press the Func key to enter the Setup Mode. Enter your Administrator Password (default 123) and press the Func key once again. Then, press B to unlock the door manually.
This site validates to XHTML and CSS web standards and is designed to be compatible with all modern browsers.
Copyright © 2002 - 2010 Artemis Solutions Group - ASG Global. All Rights Reserved.
ALL RIGHTS ARE HEREBY RESERVED PURSUANT TO 17 U.S.C. §106, AND 17 U.S.C. §106A
Use of this site is subject to our Terms and Conditions of Usage, Conditions of Sale and Privacy Policies.
